TIPS ABOUT HOW TO Extend Smok Pen Recharge Time
The Smok Pen is a new pen that was created by two guys in California. They wanted to create a cool writing instrument that appeared as if a genuine pen but had the ability to smoke a hookah. They named their product the Smok Valve and the Smok Pen. The Smok Valve has had the market by storm.
The Smok Pen has a built quality that’s just great. I came across that even though it can be an electronic pen the build quality is just as good as any of the pens that I have reviewed. It is because of how they made the very best cap. You don’t have to be worried about the cap cracking or breaking on you Smok Valve Pen.
Both biggest differences that separate the Smok Valve from other pens may be the form of the coils and just how that they are built. In general the Vape Shop coil on a Smok Pen is bigger than on other pens. I believe that they did this on purpose, to help make the pen feel more substantial.
If you take a look at a Smok Pen, you will notice that the body of the pen is round and not smooth like other pens. On the trunk of the pen there exists a little tab that houses the coil. When you press on the tab you can actually turn the heating element on / off. I really liked this feature since it allows me to use the Smok Pen 22 whenever I feel like smoking.
To use the Smok Pen it is advisable to keep the heat button pressed. After the button is pressed, the heating element will start to warm up. Once it reaches the appropriate temperature it is possible to turn off the heating element. Smok recommends using a 22mm tank. I prefer a more substantial tank, but that’s just me.
When you put your Smok Pen into the tank you will notice a indicator light come on. The indicator light will stay green unless you put your Smok Pen in to the Smok Pen charger. Once your Smok Pen has entered the charger the indicator light will turn red. It is very important always put your pen in to the charger before you apply the e-liquids to the coil heads. It is also important to do that before putting your e-liquids into the coil heads.
After you have completed this step, you should always check to see should you be at the proper temperature for the coils to fire. Or even then you should turn the power off and try again. In case you are still not satisfied together with your Smok Pen then I suggest you take it in for some troubleshooting. This is exactly what I’d call the “troubleshooting process” because sometimes things just usually do not work as they should. I suggest that you perform the next two steps, then go on and check the Smok Pen to see if it still gets the electronic charging port.
Before you go any further you should take away the battery from your own pen and unscrew the magnetic cap. You need to then remove the plastic sleeve that holds the sub-ohm. You will find a wire that runs through the Smok’s body which is green in color. You need to loosen this wire using pliers. After you have loosened this wire after that you can access the sub-ohm. You should then remove the wire from the Smok’s body and carefully insert it into the Smok pen’s electrical port, being careful to not touch any of the coils.
Once you have placed the sub-ohm tank in to the pen you need to then place the rest of the components including the wattage, the batteries and the heating element in to the included microwaveable microwave oven. Start the power and follow the on screen instructions. You need to place the pen’s battery in to the microwave and activate the setting. You need to then wait approximately 30 seconds before turning it cool off. When you initially put the pen into the microwave the electronic reading will show a low voltage protection setting. If this setting does not automatically get set you then should follow the on screen instructions.
After the Smok Pen has reached the temperature that it requires to reach you need to then connect both wires to the negative and positive on the positive post on the Smok unit. You should then connect another end of the battery to the negative post on the negative side of the Smok unit. The ultimate step would be to connect the positive cable to the bottom of the Smok’s power switch.
After all the components have been placed in to the pen, you should turn the energy on. After the first test run, you have to be able to start to see the battery life indicator light seriously. If you do not see any sign of life from the Smok Pen, you should take away the battery from the pen and then replace it with a fresh one. For your convenience gleam green light which might be pressed so as to confirm the battery charging status. When you have done these things and you also do not start to see the green light indicating charging, you should replace the battery.